Proven HVAC Solutions in Kissimmee, FL

Performed a complete diagnostic on the Carrier system for the downstairs zone (single A/C system with zoning damper controls) due to no cooling concerns. Upon inspection, found the zone damper motor stuck in the closed position, preventing proper airflow to the downstairs area. Manually opened the damper and disconnected the motor to leave the damper in the open position temporarily until replacement can be completed. Spoke with the PM & HO, and approval was obtained for zone damper motor replacement, along with signed contract agreement. Replacement part was not available at the time of service. Return visit is scheduled for Wednesday to install the new damper motor. Also completed the first maintenance visit under the customer’s maintenance agreement. Checked full system operation in cooling mode, including: * Compressor amperage * Condenser fan motor amperage * Blower motor amperage * Temperature split * Subcooling * Superheat System is currently operating within normal paramet

Performed diagnostic on heat pump Goodman condenser & Carrier air Handler 2.5 ton unit serving the guest room over the garage. The system is 21 years old and currently down at this time. After a full inspection, I found the unit requires multiple major repairs due to the age and overall condition of the equipment. I provided the customer with a full estimate for all necessary repairs. Due to the extent of repairs needed and the age of the system, I recommended full system replacement as the most cost-effective long-term solution. Customer requested a new system proposal instead of moving forward with repairs. I contacted the office and created the replacement lead so the proposal can be sent over. Customer also advised they have a second company scheduled to evaluate the system tomorrow for another opinion. The unit remains temporarily down at this time pending the customer’s final decision.

Diagnosis on a 2017 Carrier unit. Upon starting system up found indoor fan not running. Verified high and low voltage going to the motor confirming that the blower motor is bad. System is under parts warranty.

Performed a diagnostic on a 5-ton Goodman unit. Found the indoor unit running and the thermostat calling for cooling, but the outdoor unit was not running. Diagnosed a failed dual capacitor as the cause of the issue. Contacted the property manager, Rob, and received approval for the repair. Replaced the dual capacitor and tested system operation. Checked system pressures, subcooling, superheat, temperature split, and overall system performance. System is currently operating properly and cooling at this time. Performed a quick unit inspection and found the condenser contactor is badly pitted and recommends replacement. Inspected the indoor air handler and found bacterial growth inside the cabinet and underneath the evaporator coil. The evaporator coil is heavily impacted with dust and bacterial buildup, with approximately 45% of the coil surface restricted. Recommended pulling and cleaning the evaporator coil, sanitizing the air handler cabinet, replacing the condenser contactor, and

Performed first preventive maintenance under the Comfort Temp maintenance agreement. Completed full system inspection and tested operation in cooling mode. During inspection, I found the dual capacitor was weak/bad. I presented repair options to the homeowner, and she approved the capacitor replacement, which was completed during today’s visit. Additional findings during unit inspection: * Condenser contactor is pitted and showing signs of wear; replacement is recommended to prevent future failure. * Bacterial growth present inside the air handler cabinet; microbial sanitizing treatment is recommended. * No surge protection installed on either the air handler or condenser; highly recommend installing surge protectors to protect electrical components. * UV light system is recommended to help control microbial growth and improve indoor air quality. I also discussed equipment condition with the homeowner. The system is approximately 12 years old. I reviewed replacement options due to

Performed a diagnostic on a 5-ton Goodman unit. Found the thermostat wire at the outdoor condenser was badly damaged, which could cause a future short. Also found the system drain line was extremely clogged, which was the reason the unit was not cooling properly. I brought both issues to the homeowner’s attention and recommended a Level 2 drain cleaning. The homeowner approved the repair. Completed repairs by replacing the damaged section of thermostat wire to the condenser and installing protective shielding over the wire. Cleaned the drain line using a drain snake and flushed the line with approximately 8 gallons of hot water until the water flowed clear. After repairs, tested system operation. The unit is now cooling properly. Checked system pressures, subcooling, superheat, temperature split, compressor amperage, condenser fan motor amperage, and blower motor amperage. All readings were within normal operating range, and the system is operating properly at this time. Recommende

Performed maintenance on a 2019 York heat pump system Recommended replacement of the contactor, installation of locking caps, a full microbial treatment to disinfect the system, installation of a UV light to prevent future biological growth, and surge protectors for both the indoor and outdoor units. Customer approved all recommendations. Completed the following work today: * Replaced the contactor * Installed locking caps * Performed microbial treatment and system disinfection * Installed UV light system * Installed surge protectors on both indoor and outdoor units

SERVICE SUMMARY: Preventative maintenance completed on 2013 Carrier unit. Tstat set to 75 and satisfied. Filter was clean. EVAP coil was dirty . Blower wheel was dirty . Blower motor was pulling 1.67A and good per data plate. Outdoor condenser fan motor was pulling 1A and good per data plate. Compressor was pulling 8A and good per data plate. Capacitor was an 50+5 and in tolerance. Performed premium drain serviced with viper spray and drain solve. Condenser coil is clean. System refrigerant pressures were good and in tolerance after stabilizing. System is heating and cooling properly. RE: WIFI ISSUES: issues that customer has been having losing connection with her Wi-Fi thermostat or caused by, a intermittently clogged drain line. The float switch was angled up when we arrived and the drain was backed up. The return box was wet. IMPORTANT INFORMATION: This interior of this air handler unit has extensive (more than normal) microbial growth accumulation. The blower wheel requires cle

Performed diagnostic on a 2021 Rheem 2-ton air conditioning system installed in 2022 for complaint of evaporator coil freezing up. Upon arrival, the system panels were already removed and the ice had completely melted. Reinstalled all covers and tested system operation. Checked refrigerant pressures and found the system operating low on refrigerant, indicating a leak in the sealed system. Discussed leak search procedure with customer and advised that if the leak was located using an electronic leak detector, the leak detection charge would be $149. Performed leak search and confirmed a refrigerant leak at the evaporator coil. Video documentation was taken and uploaded to the system. Contacted the office to verify warranty status and confirmed the evaporator coil is covered under parts warranty through 2032. Provided estimate for evaporator coil replacement under parts warranty but refrigerant isn’t the refrigerant R410a cost $99 per pound; however, customer declined repair at this ti

Performed preventive maintenance on Carrier unit. Checked system operation in cooling mode, including system pressures, subcooling, superheat, temperature split, compressor amperage, condenser fan motor amperage, and blower motor amperage. System is operating properly at this time. Inspected electrical components and found the capacitor testing within manufacturer tolerance. However, the contactor was found to be badly pitted. Recommended replacement to prevent future failure, and customer approved repair. Replaced contactor and verified proper system operation. During inspection, found the SS2 safety float switch stuck in the closed position, which could prevent proper condensate overflow protection. Brought this to the customer’s attention, and customer approved replacement. Replaced the SS2 safety float switch and tested operation to confirm proper functionality. Cleaned condensate drain line and drain pan, and applied Viper treatment for drain maintenance. Removed debris from in